2007 RANGER WIRING DIAGRAM
Rangers - su Amazon
AdRisparmia su Rangers. Spedizione gratis (vedi condizioni)
2007 Ford Ranger wiring schematic diagram to install a - Fixya
wwwa››Ford›Ranger›2007 Ford Ranger FX4 Off-Road2007 Ford Ranger wiring schematic diagram to install a command start - Ford 2007 Ranger FX4 Off-Road questionHi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US. Here's a link to this great service Good luck!Disconnect the negative battery cable.
Remove the gearshift lever assembly from the control housing.
Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
Raise the vehicle and support it safely.
On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
Disconnect the speedometer from the transfer case/extension housing.
Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
Place a wood block on a service jack and position the jack under the engine oil pan.
On 4WD vehicles, remove the transfer case from the vehicle.
Remove the starter motor.
Position a transmission jack, under the transmission.
Remove the transmission-to-engine retaining bolts and washers.
Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
Lower the transmission jack and remove the transmission from the vehicle. To install: Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
Install the starter motor. Tighten the attaching nuts.
Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
On 4WD vehicles, install the transfer case.
On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
Connect the hydraulic clutch line and bleed the system.
Install the speedometer cable.
Check and adjust the fluid level.
Lower the vehicle.
Install the gearshift lever assembly. Install the boot cover and bolts.
Reconnect the negative battery cable.
Check for proper shifting and operation of the transmission.
The above was pulled frrom: http://wwwzone/shopping/repairGuide?pageId=0900c152800391da
hope this helps0The diagram you seek is below.0These 3 codes have to do with restraint system.
B2292 Seatbelt pretensioner fault.
B2293 Passenger front airbag fault.
B2691 Seatbelt buckle switch circuit fault Fter side.0if u can gain access to the ignition switch wiring use a testlight and probe each wire while turning the ignition at start position of these wires shld have power during starting position and release it again to confirm wire goes directly to the trasmission multi lever position swicht (mlp) MLP is mounted just outside the transmission shifting lever ganged togethere the corresponding return wire using the testlight. You may need someone to help you do the job return wire usually go to a relay on your fuse box on the engine compartment from relay to the starter.0When you tell us "wiring diagram", is for one specific circuit or you are refer to the firing order?0
2007 Ford Ranger Engine Wiring Diagram - Downloaddescargar
1998 ford ranger engine diagram wiring library fuse box chevrolet silverado 1999 2007 1992 ford ranger engine diagram 1999 ford ranger 30 engine. 1990 ford ranger